19 Simple Steps To Artificially Rearing Discus Fry
Step 1:
Give the parents a 1.5-2" PVC pipe 14-16" long to let them spawn on. pH must be below 7 and water used throughout this process must be soft (around 100 ppm and uS around 120-180). This helps the eggs in sticking.
Step 2:
Make sure that the males is fertilizing the eggs, otherwise any attempt is futile.
Step 3:
Wait two hours after spawning is finished.
Step 4:
Using a 1 gallon glass jar, fill it with the tank water the parents (& eggs) are in. Put the PVC in the jar (quickly and calmly).
Step 5:
Place the jar in a small 5 gallon tank filled with water at 84f (50w heater is required). Also put a hydrospnge (by far my personal choice in sponge filters). in the tank and turn it on. This will keep the jar warm and allow the tank to cycle. I always have filters in my 5 gals so they are cycled.
Step 6:
Add an airstone to the jar. Turn it on medium so that there is a good currrent in the jar (dont blast the eggs though).
Step 7:
Add three drops of methyl blue. Other people may reccomend more, but I believe that it may cause fry loss. Three drops works well and allows you to observe the eggs.
Step 8:
Wait. They will begin hatching (if they are fertile and the correct water perameters/hardness/uS are present) in two days (about).
Step 9:
Wait. They will start free swimming in two-three days (mostly three). They will be clogged in a bunch on the bottom of the tub during this period and will untangle when good and ready.
Step 10:
As soon as they become free swimming, give them their first feeding. Use artificial plankton and rotifers (a.p.r.) used for feeding marine filter feeders. Add an amount the size of the winding screw on your watch (it was the only thing I could see around my desk of to relate how small small MUST be (g)).
Step 11:
4 hrs later remove the jar from the 5g tank and float a small rubbermaid tub in the 5g tank. Place the airstone in the tub (turn it off first). Use a baster to move the fry to the little tub. Fill the tub with the jar water 75% and 5g tank 25% until the tub is almost full. Turn the airston on to a small blip...blip..blip..... enough to keep the surface of the water in the tub broken. Keep the tank with the tub covered to avoid cooling/evap/drafting on the tub.
Step 12:
Add the same small amount of food.
Step 13:
4 hrs. later do a fifty percent water change of tub water using the baster. I go from the baster to another small tub before I dump the water in case I suck up some fry (so I dont dump them out). Replace the tub water with the tank water (Hey, notice the tank water is the same temp as the tub water!). Feed same small amount.
Step 14:
4-6 hrs later do a 90% change using the above method. (NOTE: eventually the 5g starts to get low. NEVER (REPEAT VERY LOUDLY, NEVER EVER) fill the 5g untill the tub water has been changed and refilled. If you do fill the 5g tank prior to filling the tup, the temp may not be exactly the same and when you fill the tub afterwards you might watch the babies go into shock...they WILL NOT recover! (This cost me A LOT of fry to figure this out!).
Step 15:
Repeat 90% water change and feeding every 4-6 hrs. (8 at the most so you can sleep, I've gone 10 before, but dont recommend it unless the is nothing you can do about it).
Step 16:
On the second day of free swimming, add a tiny amount (VERY TINY) amount of NEWLY HATCHED baby brine shrimp (b.b.s.) with every feeding. Dont stop using the a.p.r. at this point. Continue performing step 15. a.p.r. shows grey bellies, b.b.s. shows pink bellies.
Step 17:
Continue feeding a.p.r. and b.b.s. for one week. All bellies should show pink by end of week.
Step 18:
Once all bellies show pink discontinue the a.p.r. and continue the b.b.s. Keep performing step 15.
Step 19:
One week later you should have lots of fry the size of baby angelfish. Let them go into the 5g tank and feed them there from now on. Keep the tank clean and watch the water changing temp. A once a day water change is good enough. The rest is standard baby fish stuff!
Source Link
No comments:
Post a Comment